With v2 firmware update, correcting many flaws of the previous 9X, plus inbuilt 2.4Ghz (no daggy second antenna) this is a quality, reliable 2.4Ghz system suitable for beginners and pro pilots alike. Get that locked-in feeling that only 2.4Ghz glitch free technology can provide. Ultra fast reaction times and interference free control of your model is only achievable with this 2.4Ghz technology.
Without a doubt, the best value 9Ch system available!
Number of Channnel: 8ch ppm/9ch pcm Display: 128*64LCD Support Type: Heli/Acro/Glid Support user: 8 Stick model: 4 Encoder type: ppm/pcm Subtrim: Yes Simulator Interface: Yes Buzzer: Yes Low Voltage Show: Yes
Important. The TURNIGY 9X has been reflashed with the new v2 firmware, fixing previous menu and mixing issues. This firmware flash is only available from our TURNIGY 9X system as we flash each unit in our office before it is shipped. Purchases of any other rebranded version of the TURNIGY 9X will not have the latest firmware and patches (even the OEM factory does not have these updates).
NOTE: "SWITCH ERROR" means you have one of the switches in the wrong position when you turn the radio on. It is not a fault.
There are no perfect match batteries that I could find. I use "Turnigy 2650mAh 3S 1C LLF Tx Pack (Futaba/JR)" PRODUCT ID: T2650.3S.1C and "ZIPPY Flightmax 2500mAh Transmitter Pack (Futaba/JR)" PRODUCT ID: ZIP25003S3C with the default firmware on the transmitter. On these batteries I use the connector that looks like a JR servo connector because I can plug it in either way as the two outer pins of the battery connector on the transmitter are connected on the PCB. "Turnigy 9XR Safety Protected 11.1v (3s) 2200mAh 1.5C Transmitter Pack" PRODUCT ID: 9171000183 does NOT fit and the battery bay have to be enlarged for it to fit.
Hi, I use the Rhino 2620mAh, product ID R2620-TX-3, and it's very close to perfect to me. It fits well (there is no loss space, trust me *) ), and just like handyjap, use the JR servo plug and there is no risk of voltage inversion.
I cannot get the flaps to work on my Turnigy 9X with 8ch receiver. Throttle, rudder, elevator and ailerons all OK. I have tried the flap servos connected to all unused receiver channels in combination with operating all switches and knobs on the transmitter but no combination will work. Any help will be greatly appreciated...
Flaps on 3 pos switch.
Step 1 Plug the flaps (Y-lead) into channel 7 of your receiver
Step 2 In the AUX settings set channel 6 to THRO HOLD
Step 3 In the MIX Settings set MIX1 STATE=ACT, MASTER=FLP, SLAVE=AUX, OFFSET=000, UPRATE=000, DNRATE=000, SW=NOR
Step 4 In the MIX Settings set MIX2 STATE=ACT, MASTER=FLP, SLAVE=AUX, OFFSET=000, UPRATE=-046, DNRATE=046, SW=ID1
Step 5 In the MIX Settings set MIX3 STATE=ACT, MASTER=FLP, SLAVE=AUX, OFFSET=000, UPRATE=-100, DNRATE=100, SW=ID2
Optionally adjust the Uprate and Dnrate settings to your desired levels.
You are welcome, and thanks for crediting. Also if you want an scale look on your flaps you can use Turnigy 3 Channel Servo Speed/Direction Regulator, PRODUCT ID: TSSR-3, very small, light and easy to use. Nice flights.
I havebought this TM, and at first try I wanted to use with an 1000mah 7.4V battery (because it has the same 3pin connector). It had some sparks, and a not so delicious smell, and now the TM does not switch on even with 8 1,5V battery.
Can someone help me with any type of information? Can this be repaired? Can you show any video or image about the part or element that needs to be changed?
Pls give me some hint, because I've in front my first scratch build quad, and can't even try it.
I'd give this radio a 5 star rating but there are a few minor things that subtract points. -One is that putting the batteries is a hassle, the 8 AA cell holder is OK, but the cable gets on the way of the cover and it takes a while to be able to close it, there's a lot of pinching of the cables involved so I shouldn't wonder if the insulation fails sooner or later requiring a replacement of the cables. -Second is the very annoying and loud BEEEEP!!! you get with every-single-click you do on the buttons, seriously stressing to set up the radio at home, not good for conjugal life. To fix that I cut the leg that goes from a transistor to the speaker and added a 220 Ohm resistor in between. -Third, no manual comes with the radio. -Fourth setting up a V-Tail was a mind bending affair, I succeeded but I couldn't grok the logic of the procedure.
Besides those things it's a good product.
25 comments. Reply..
8 thumbs up!
I have one of those and i have kinda problem with display, there is some cold conract, on mainboard, ans still bordering me all the time( otherwise seems ok the menu and functions.
6 comments. Reply..
8 thumbs up!
I purchased this transmitter & Assan XJ8 module from HC. First I got around the switch error bug (thanks to that reviewer) For me the Assan XJ8 just flashes red once on start up, but gives no steady red LED & will not go into pairing mode. Assan say they don't know the problem & suggest putting XJ8 in another TX (I don't have one) Anyone know how to test if TGY 9X or Assan is the problem? Thanks
11 comments. Reply..
7 thumbs up!
Great range - over 3000m, but realy to big receiver. Also dont like to small battery compartment, and antenna linked with wire. You Also can't mix with AUX cahnnels - you can oly mix first 4 cahnells. No manual - It could be at least link at this product to download manual for Turnigy 9x. Also don,t like that this transsmiter in almost never in stock, or that there smaller 6 ch receivers I waiting for more 3 months So from me only 3 stars.